Views: 50 Author: Site Editor Publish Time: 2026-11-17 Origin: Site
Hydraulic gear pumps are widely used in construction machinery, agricultural equipment, and industrial hydraulic systems. Although they are known for their relatively simple structure and reliable operation, problems may still occur during long-term use.
Common symptoms include insufficient pressure, low flow, abnormal noise, overheating, and oil leakage.
Understanding the possible causes of these problems can help equipment operators and maintenance technicians identify faults more efficiently and reduce unnecessary downtime.
This guide explains common hydraulic gear pump problems, their possible causes, and basic troubleshooting methods.
Insufficient pressure is one of the most common problems in hydraulic systems.
Possible causes include:
Excessive internal leakage inside the pump
Worn gear teeth or bearing surfaces
Damaged seals
Low hydraulic oil level
Incorrect pressure relief valve settings
Leakage in the hydraulic circuit
Check the hydraulic oil level.
Inspect the hydraulic lines and connections for leakage.
Check the pressure relief valve and its setting.
Inspect the pump for abnormal wear or internal leakage.
Compare the measured pressure with the system's specified operating pressure.
If the pump has excessive internal wear, repair or replacement may be necessary.
Abnormal noise may indicate problems with oil supply, air entering the system, mechanical wear, or improper installation.
Common causes include:
Air entering the pump inlet line
Restricted or blocked suction filters
Insufficient hydraulic oil supply
Excessive oil viscosity
Worn internal components
Misalignment between the pump and drive shaft
Excessive rotational speed
Check the hydraulic oil level.
Inspect the suction line and connections for air leakage.
Check whether the suction filter is blocked.
Confirm that the hydraulic oil meets the equipment requirements.
Inspect the pump installation and drive coupling.
Check whether the operating speed is within the manufacturer's specified range.
A common cause of loud noise is cavitation, which may occur when the pump cannot receive sufficient oil at its inlet.
Continued operation under cavitation conditions may damage internal pump components.
Low flow can cause slow actuator movement and reduced equipment performance.
Possible causes include:
Incorrect pump displacement
Low rotational speed
Internal pump wear
Excessive internal leakage
Blocked suction filter
Air entering the hydraulic system
Incorrect hydraulic oil viscosity
Check the pump's rated displacement.
Confirm the actual rotational speed.
Inspect the suction filter and inlet line.
Check for air entering the hydraulic system.
Measure the pump's actual flow rate if suitable testing equipment is available.
Inspect the pump for internal wear.
If the pump cannot deliver the required flow under the specified operating conditions, further inspection or replacement may be required.
Excessive hydraulic oil temperature may reduce system efficiency and accelerate component wear.
Common causes include:
Excessive system pressure
Continuous operation at high pressure
Incorrect hydraulic oil viscosity
Restricted oil flow
Internal leakage
Insufficient cooling capacity
Excessive mechanical friction
Check the system operating pressure.
Inspect the hydraulic oil level and condition.
Confirm that the oil viscosity meets the equipment requirements.
Check the cooling system.
Inspect the pump for excessive internal leakage or mechanical friction.
Check whether the pump is operating within its rated speed and pressure range.
Overheating should not be treated as a pump problem alone. The entire hydraulic system may need to be inspected.
Oil leakage may occur around the shaft seal, housing joints, or hydraulic connections.
Possible causes include:
Damaged shaft seals
Worn sealing surfaces
Loose connection bolts
Damaged O-rings or gaskets
Excessive system pressure
Improper installation
Clean the pump surface to identify the exact leakage location.
Check the shaft seal and surrounding area.
Inspect the inlet and outlet connections.
Check the condition of O-rings and gaskets.
Confirm that system pressure is within the specified range.
Replace damaged seals or sealing components with suitable parts. If the housing or shaft has been damaged, a more comprehensive repair or pump replacement may be required.
Not every pump problem requires a complete replacement. The decision depends on the pump's condition, the availability of replacement parts, and the cost of repair.
The problem is limited to replaceable seals.
The housing and main internal components remain in acceptable condition.
Replacement parts are available.
The pump can meet the required performance after repair.
The pump housing is cracked or severely damaged.
Internal components have excessive wear.
The pump cannot maintain the required pressure or flow.
Repair costs are close to or higher than replacement costs.
The pump has repeatedly failed after previous repairs.
The final decision should be based on a proper inspection and performance testing.
Proper operation and maintenance can help reduce pump failures and extend service life.
Recommended practices include:
Use hydraulic oil that meets the equipment manufacturer's specifications.
Replace hydraulic oil and filters according to the maintenance schedule.
Keep the hydraulic system clean.
Inspect suction lines and connections regularly.
Avoid operating the pump beyond its rated pressure and speed.
Monitor abnormal noise, temperature changes, and oil leakage.
Ensure correct pump installation and shaft alignment.
Preventive maintenance is generally more cost-effective than waiting for a major hydraulic system failure.
Huizhou Loyal Hydraulic Co., Ltd. supplies hydraulic pumps and related components for construction machinery, agricultural machinery, and industrial equipment.
If your hydraulic gear pump has developed a fault and requires replacement, providing accurate product information can help reduce identification errors.
When contacting us, please provide:
Original pump model or part number
Equipment brand and model
Photos of the pump and nameplate
Relevant technical specifications, if available
Our team can help check product information and identify a suitable replacement option.
Possible causes include internal wear, excessive leakage, damaged seals, low oil supply, or problems with the pressure relief valve. The hydraulic system should be inspected to identify the actual cause.
Common causes include air entering the suction line, cavitation, a blocked suction filter, insufficient oil supply, incorrect oil viscosity, or worn internal components.
Yes, some problems can be repaired by replacing seals or other serviceable components. However, severe internal wear or housing damage may require pump replacement.
Possible causes include excessive pressure, internal leakage, restricted oil flow, incorrect oil viscosity, insufficient cooling, and excessive mechanical friction.
Use the correct hydraulic oil, maintain oil cleanliness, replace filters regularly, operate within the specified pressure and speed range, and inspect the hydraulic system for leakage or abnormal noise.
Need a replacement hydraulic gear pump? Contact Loyal Hydraulic with your original model number, part number, or product photos for assistance.